Can I upgrade to Kong from Mega?

DD-WRT v24-sp2 (07/18/10) big
(SVN revision 14826M NEWD-2 K2.6 Eko)

pffft
well
i installed;

Router Name
DD-WRT
Router Model
Netgear WNR3500v2/U/L
Firmware Version
DD-WRT v24-sp2 (04/11/11) vpnkong - build 16774M

but it seems the usb port on the router is DEAD
when i put in a HD no LED's flash
a USB stick also no leds or anything

im sure its not the drive or stick sisce i tested them in a "normal" USB port

i did the 30-30-30 reset but no dice

i want to do the OPTware install thingy but then i really need the USB drive

surfing the boards for is VERY timeconsuming since the info around is fragmented to say the least

i went for this KONG mod because this said USB support was enabled by default AND it was succesfully tested on a WNR3500L

but it seems the USB port is simply dead

anyone have any tips?

or (preferably) a working configuration?

WNR3500L
firmware type and build??

thanks

Hi, I want to try this firmware but I prefer the original asus RT-N16, it is possible to add miniDLNA server to original asus firmware 1.0.2.3?
I hope that works to stream videos from usb drive connected to my router to my samsung LE32C550 tv.
THX

Hi Kong, is it possible or impossible with the E3000 to move the Privoxy portion into the DLNA version? I think it would be a huge improvement for more users that are initially switching to your build. I use Pixelserv and I can tell Privoxy would be a good solution.

Hi Kong,
I have been trying for two weeks to get DD-WRT V24 to build from source. I am targeting the WNR3500L. My build system is 64 bit Unbuntu 9.10. I have downloaded the current toolchains from DD-WRT.com and source code but cannot get it to build. I have followed the "tutorial on building DD-WRT" with no success. What build system and toolchains are you using? Can you give me any suggestions?
Thanks in advance.
Skykingstlmo

Hi Kong,

I just bought a netgear 3500L which runs your mod perfectly.
I have another old router, WRT54GS v2, which has Broadcom BCM4712 @ 216 MHz 32 MB 8 MB, I am wondering if I could flash you mod on it since it meets the requirements.
Already googled, no results.

Thanks!

Hi Kong,

Searching online led me to this link and I would like to ask you if your kong mod will work on my generic router.

The details are as follows:
CPU Model - Broadcom BCM5354 chip rev 3
CPU Clock - 240 MHz
RAM: - 32 Mb DDR
Flash Memory: - 16 Mb
builtin USB
running DD-WRT v24-sp2 (12/24/10) mega - build 15962

Right now, the unit is acting as WAP with 2 BSSIDs, one for my internal network and another one for public (I am broadcasting my internet for students who wants to connect to the internet for school works). SNMP is running and is linked to odmon.com for monitoring purposes.

Your inputs are highly appreciated

More power to you and this website

Does Kong Mod support IPv6? I have it selected in options but Vuze displays only IPv4 connection status as OK. When I bypass the router and go direct from my PC it does show IPv6 as active and connected, so I know my Vuze config and my ISP supports it.

Is it because the router itself (Netgear WNR3500L) lacks this ability?

Enquiring minds need to know...
Gorb

Thanks Jondlou, that script worked like a charm! At first I thought not but I restarted Azureus and IPv6 was running fine. I do use OpenDNS but couldn't figure out that OpenDNS instructional on the wiki page. If I set my router to "Use local DNS" everything stops working - both Internet and local network even though I had all the other settings already as you specify.

Could you please add samba vfs modules.
Right know I use samba from optware installation which has vfs modules, but if there is enough space left in the firmware why not add the vfs modules. (fyi: I use vfs dirsort)

Hi,
does this firmware support Netatalk 2.2?