it works as described, on my case, the final telnet attempt didn't present the authentication challenge, telnet to the box opened up the BusyBox below:
BusyBox v0.60.0 (2008.06.06-03:40+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
# help
Built-in commands:
-------------------
. : break cd continue eval exec exit export help login newgrp
read readonly set shift times trap umask wait
#
Hope it helps.
Hi,
I downloaded the zip file and extracted it.Followed the steps given in the word document,but its not working for me.I got an error.
My Operating System : Windows7 Home Premium
Netgear Model:DGN 1000
Output:
**************
C:\Telnet Enable>telnetEnable.exe 192.168.0.1 30469A22062F Gearguy Geardog
send failed: 10057
Please help me to solve the problem.
View unverified member's comment - posted by hargy
Hi,
We can assign any ip address of our modem(my modem ip addr:192.168.0.1). we have followed the given steps in the document, even though we are getting an error. see the below log
C:\>cd "Telnet Enable"
C:\Telnet Enable>telnetEnable.exe 192.168.0.1 30469A22062F admin password
send failed: 10057
Regards,
jawahar
Hi,
I've tried this on my DGND3700 and it doesnt work. The utility returns without any problems but telnet is not enabled.
The only thing I can this is:
When I bought my router the shrink wrap had been damaged. I wonder if someone had bought then returned the product. (It looked untouched although)
Is it possible someone has changed the telnet password on my router then disabled telnet?. Is that possible? Can you reset the console password by reflashing the device?
Cheers
As far as I know, it doesn't work on DGN routers. I have one here.
It definitely doesn't work on the Orange (UK ISP) provided DGN1000. You can tell if it's from them if the router has RG in the firmware version.
The reason why it doesn't work on that one is that there is no telnet binary on the router!
You can access it via the internal serial port though! You can find this right in the center of the board. It looks like 4 golden circles in a vertical line. The order from top to bottom is GND, TX, V+, RX.
This also allows you access to U-Boot when the router starts up.
Hope this helps some people.
Like Nebster said there is no utelnetd binary on dgn1000 but you can compile it by yourself upload and run :)
(guide posted on binblah.blogspot.com)
if you wanna just run some commands u can use syscmd webpage
http://192.168.0.1/syscmd.htm
I have followed this comments to get to my router. It is WNR3500L router. I have lost my Admin password to the regular browser utility and to see if by accessing it by telnet will allow me to get it or change it. I have tried the following command with no luck.
telnetEnable.exe 172.16.1.1 E091F5869530 Gearguy Geardog
I get this error: bind fail: 10048
Copyright © 2012
Capable Networks LLC.. All Rights Reserved.
RSS |
Privacy Policy |
Advertise With Us |
Terms of Use |
About Us |
Contact Us |
Site Map
Our Capable Community Network:
DVR playground |
Explore3DTV |
MediaSmart Home |
MotoDash |
My Open Router |
Pogoplugged |
DijitCommunity |
Robo Community |
Sansa Community |
TechLore |
TiVo Community |
TouchSmartDevZone
MyOpenRouter.com is not affiliated with NETGEAR®. NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks of their respective holder(s). © 2011 NETGEAR, Inc. All rights reserved.
Did you forget your password?
You can also log in using OpenID.
