Hi,
I have compiled the DD-WRT source but not courageous enough to burn the image to flash. Is it possible to run the image from RAM. Actually I would like to run DD-WRT image in the WGR614v8. Can anybody please come up with some ideas.
Thanks,
Categories: News, Rumors and Gossip WGR614L Open Source Router Open Source Projects and Firmware DD-WRT
Noticed this thread on DD-WRT forum. Wanted to bring in the discussion here.
-Nachi
DD-WRT supports the bcm5354 based routers, but not sure if it already supports the netgear WGR614L open source router. Can anyone through some ideas here?
WGR614L has community around it at http://www.myopenrouter.com and you may be able to get some answers on this there too.
Here is what I can find out about WGR614L at here.
"A new router platform WGR614L is coming soon and what got me excited is that this new platform is well suited for many excellent community developed firmwares like like OpenWRT, Sveasoft, DD-WRT, Tomato. This Broadcom 5354 SoC based router has 4MB flash and 16MB SDRAM - good enough to run most of these popular firmwares. In fact most of the firmwares that runs on Linksys WRT54GL should be easily (relatively speaking) portable to WGR614L."
DD-WRT supports the bcm5354 chipsets - but not sure if the firmware can be run on this rotuer unmodified.
The also have a alpha version of Tomato firmware available here.
--wrthack
March 10, 2008 8:22 AM
March 11, 2008 7:43 AM
The Code I have compiled is downloaded from
http://victek.is-a-geek.com/Repositorios/Linksys/Source%20code/1210-2006-svn5...
March 11, 2008 8:22 AM
I have gone through the DD-WRT forum as well. There I have been referenced to a Netgear 614L compatible DD-WRT version. I download this image but got a panic. It shows 'Unable to mount rootfs' and gets rebooted. Can anybody give some idea - what would be the probable cause. However I will also modify the source to run in the Netgear platform. Now it sounds good that the third party vendors also trying to make their code compatible to Netgear.:)
NETGEAR
- member since: 12/13/2007
- rank: 11 of 4555
- 1 articles authored
- 4 blog entries posted
- 3 forum threads started
- 84 comments
March 11, 2008 2:07 PM
Great that you could compile the code.
you could try to use the boot_wait=on nvram settings in the WGR614L to boot from a tftp server. In this case you should use the embedded ramdisk option in the kernel to make sure you do not have to burn the rootfs into the mtd.
The failure to mount rootfs is the problem I have also got. Let me know if you make further progress on this.
Moderator
- member since: 01/23/2008
- rank: 4 of 4554
- 9 articles authored
- 6 forum threads started
- 149 comments
March 22, 2008 12:03 PM
Anyone tried the later updated versions shown in the above thread? Before I start playing it would be nice to hear others results.
...Follow Me on Twitter... Why is it after I push 1 for English I still can't understand the person on the other end?...
June 30, 2008 4:06 PM
updated: June 30, 2008 4:42 PM
hrlevy said: where did you find the 'the DD-WRT source ' ????
This should help a little...
http://www.dd-wrt.com/wiki/index.php/Development#Source_Retrivial
svn co svn://svn.dd-wrt.com/DD-WRT
Moderator
- member since: 01/23/2008
- rank: 4 of 4554
- 9 articles authored
- 6 forum threads started
- 149 comments
June 30, 2008 10:29 PM
updated: June 30, 2008 10:29 PM
It looks like your link to the svn download is broken. You can either re-edit your post or post it again. I would love to check out the source.
...Follow Me on Twitter... Why is it after I push 1 for English I still can't understand the person on the other end?...
July 1, 2008 3:14 AM
http://tortoisesvn.tigris.org/
BrandonC said: It looks like your link to the svn download is broken. You can either re-edit your post or post it again. I would love to check out the source.Ok, to download SVN in Windows you have to install TortoiseSVN or an equivalent.
http://tortoisesvn.tigris.org/
July 8, 2008 7:11 AM
Hi. I think that the best thing is to provide patches and/or other support directly to the actual development team of dd-wrt (BrainSlayer, eko and others) and link the download page to the official download section of the dd-wrt site. I think this is the best to avoid a mis-syncronization from latest image files from official dd-wrt team and this site (the revision downloadable form here is a 9281, the latest from eko is 9856) and because on the official site is possible to retrive varius "flavours" of dd-wrt (micro, standard, nokaid, etc.)
Another thing is to update the official wiki with the flash how-to for this router.
In other words, I think that maintain a separate download section and a separate point of reference for dd-wrt isn't a good idea.
August 20, 2008 2:59 PM
I just flashed my wgr614v8 to the latest DD-WRT v24-sp1 which I downloaded from this site. The flash went fine and configured WDS with my airport express as the repeater, but two things I'm concerned about. One, the power LED does not stay on any longer, only goes on when I reset the router by pressing in the reset button on the back of the unit or resetting via dd-wrt menu. Two, the "check" and "internet" LEDs are constantly lit and in amber color instead of green. Is this a known bug with the latest DD-WRT for the WGR614v8 or did I screw up my router, though DD-WRT is working great! Man, what a differnce it made. Increased the range by two bars. I was in the good range, three bars, and now I'm in Excellent range, 5 bars.
Member
- member since: 10/14/2008
- rank: 1 of 4554
- 4 articles authored
- 16 forum threads started
- 406 comments
October 17, 2008 7:47 AM
hrlevy said: where did you find the 'the DD-WRT source ' ????
The following link provides both the source code and the toolchain :
December 13, 2008 10:41 AM
Hi,
I have installed the wireless G router WGR614 v9. I want to put a network password so that the connectivity can be only be used by restrcited people. Can some one guide me how that password can be put into place.
Regards
December 18, 2008 3:41 AM
i flashed my WGR614 v8 with the DD-WRT v24-sp1 and now the power light blinks and i can't access the router through 192.168.1.1 . I have tried several times to do a hard reset and it seems to reset but i still can't access it. did i brick my router?????
NETGEAR
- member since: 12/24/2007
- rank: 2 of 4554
- 4 articles authored
- 4 blog entries posted
- 6 forum threads started
- 281 comments
December 18, 2008 6:09 AM
Where do you want to put network password ?
If you are connecting to the router via wireless medium then you can use wireless security like WPA/WPA2 or WEP where you can specify password.
If you are using Ethernet connection then there is no such password protection. However you can specify some firewall rule such only your machine can access through that router.
You can also change the login password of WGR614v9 so that no one can access the board also.
Administrator
- member since: 01/02/2008
- rank: 3 of 4554
-
location:
United States
- 18 articles authored
- 43 forum threads started
- 93 comments
December 18, 2008 12:15 PM
po said: i flashed my WGR614 v8 with the DD-WRT v24-sp1 and now the power light blinks and i can't access the router through 192.168.1.1 . I have tried several times to do a hard reset and it seems to reset but i still can't access it. did i brick my router?????
There is a newer version of DD-WRT available for the WGR614L that was just uploaded a few days ago, you may have better luck with it.
You can download the newest version, uploaded on 12/16/2008 (v11205) by clicking here.
It's available in BIN and CHK formats.
Make sure to check the downloads area on the site and the homepage for the newest versions of DD-WRT for your router. If you have any more questions, please post them to our forums for the router experts to answer :)
Peter Redmer
Administrator
Visit my blog, "Caffeinated Pixels"
Follow Me on Twitter
December 19, 2008 3:04 PM
updated: December 19, 2008 3:05 PM
I am not a big fan of DD-WRT myself... an openwrt man :D
please do not use DD-WRT
December 19, 2008 5:02 PM
Thank you i downloaded the chk format but i beilieve that i bricked my router, WGR614 v8. i get an ip address but i can't access it and my power light keeps blinking.
December 31, 2008 6:21 PM
I find it funny that these things are always being posted.. since it was unlocked on openwrt first and then dd-wrt grabbed the code and got the publicity... :(
please do not use DD-WRT
NETGEAR
- member since: 12/24/2007
- rank: 2 of 4554
- 4 articles authored
- 4 blog entries posted
- 6 forum threads started
- 281 comments
December 31, 2008 11:38 PM
po said: Thank you i downloaded the chk format but i beilieve that i bricked my router, WGR614 v8. i get an ip address but i can't access it and my power light keeps blinking.
If you bricked the router then I think firmware upgrade is not fully completed. You have rebooted board or switch it off before it gets completed.
You are saying that you get an ip addres. I guess you get IP address from the router dynamically. Then how can you say that you bricked your router ?
January 8, 2009 6:06 PM
I said that i might have bricked it because it won't let me access the router and the power light keeps blinking. when i do the firmware flash i put it into anyone of the 4 LAN ports correct? and not the internet port just making sure!
Member
- member since: 10/14/2008
- rank: 1 of 4554
- 4 articles authored
- 16 forum threads started
- 406 comments
January 8, 2009 10:22 PM
po said: I said that i might have bricked it because it won't let me access the router and the power light keeps blinking. when i do the firmware flash i put it into anyone of the 4 LAN ports correct? and not the internet port just making sure!Yes, you need to connect with any one of 4 LAN ports .... WAN or Internet port is not needed for firmware upgrade....
Member
- member since: 10/14/2008
- rank: 1 of 4554
- 4 articles authored
- 16 forum threads started
- 406 comments
January 8, 2009 10:26 PM
po said: i just tried it again and i get a 169.xxx.xxx.xxx ip address now. any help?
Did you try firmware upgrade ..... After firmware upgrade you should wait for a minute or may be a couple of minutes ..to allow your sytem to boot properly with new firmware ....
I think you are doing some mistake in firmware upgrade .... bcoz this firmware works OK on WGR614L ...
Add Your Reply
Sponsored Links
Copyright © 2010
Capable Networks LLC.. All Rights Reserved.
RSS |
Privacy Policy |
Advertise With Us |
Terms of Use |
About Us |
Contact Us |
Site Map
Our Capable Community Network:
DVR playground |
MediaSmart Home |
MotoDash |
My DigitalEntertainer |
My Open Router |
Pogoplugged |
Robo Community |
Sansa Community |
Sling Community |
TechLore |
TiVo Community |
TouchSmartDevZone
MyOpenRouter.com is not affiliated with NETGEAR®. NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks of their respective holder(s). © 2008 NETGEAR, Inc. All rights reserved.
