WGR614 V8 and DD-WRT update: MyOpenRouter

Moderator

member since: 01/23/2008
rank: 1 of 27868
22 articles authored
12 forum threads started
409 comments

January 20, 2010 12:50 PM

If you already have DD-WRT on the router then use the BIN file shown for your router version. The Micro version BIN file should do what you need.

http://placeshiftingenthusiasts.com/

achilles

Member

member since: 10/14/2008
rank: 134 of 27868
4 articles authored
16 forum threads started
406 comments

January 21, 2010 2:10 AM

Also it would be better to use IE for f/w upgrade instead of firefox ...... you can upload MINI version of the build also (it would provide some extra features)...
Make sure that if u have a DD-WRT f/w running on ur board , u use .bin file for upgrade and if u have default netgear f/w running on ur board u use .chk file for upgrade ...

Tysek

Member

member since: 01/11/2010
rank: 676 of 27868
1 forum threads started
3 comments

January 21, 2010 6:39 AM updated: January 21, 2010 10:51 AM

After update i heve problem power led blinking.

I make 30/30/30 reset.
On dhcp can't get Ip adres (by cable rj45)
If I set manual 192.168.1.1 and mask 255.255.255.0, my computer connected to router.
eth0 Link encap:Ethernet HWaddr 00:1c:23:89:a3:4f
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21c:23ff:fe89:a34f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:70939 errors:0 dropped:0 overruns:0 frame:0
TX packets:64958 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:24449805 (24.4 MB) TX bytes:9591419 (9.5 MB)
Interrupt:17

Ping

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.042 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.066 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.047 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.064 ms

I try try by tftp
tftp binary 192.168.1.1 -c dd-wrt.v24_mini-wgr614v8-L.chk

after this my system give me this: usage: tftp host-name [port]

I sterted tftp olny with adres "tftp 192......"
and give this order. but nothing happens

tftp> binary -c /home/tysek/Dropbox/rezurekcja/WRT614L/dd-wrt.v24_mini-wgr614v8-L.chk
tftp>

What should I do ?

Brandon C

Moderator

member since: 01/23/2008
rank: 1 of 27868
22 articles authored
12 forum threads started
409 comments

January 21, 2010 10:51 AM

Set your computer's address to something like 192.168.1.10, 255.255.255.0 and gateway to 192.168.1.1.
Then try to ping, tftp to 192.168.1.1

http://placeshiftingenthusiasts.com/

Tysek

Member

member since: 01/11/2010
rank: 676 of 27868
1 forum threads started
3 comments

January 21, 2010 10:52 AM

I give update to my post.

Brandon C

Moderator

member since: 01/23/2008
rank: 1 of 27868
22 articles authored
12 forum threads started
409 comments

January 21, 2010 11:26 AM

I assume you are running Windows.
To TFTP you need to enter
tftp -i 192.168.1.1 PUT yourfirmware.chk

the -i after tftp tells it binary and then the adress or your router, then "PUT" tells it to send the firmware you name onto the router.

http://placeshiftingenthusiasts.com/

Tysek

Member

member since: 01/11/2010
rank: 676 of 27868
1 forum threads started
3 comments

January 21, 2010 12:49 PM

Thanks for your help and time

I'm using Linux, but i quickly install XP, and tftp, It works :-)
I don't know why i wasn't working in Ubuntu.

Thanks a lot

Brandon C

Moderator

member since: 01/23/2008
rank: 1 of 27868
22 articles authored
12 forum threads started
409 comments

January 21, 2010 6:58 PM

Suweet! Glad you go it working. Rock on!

http://placeshiftingenthusiasts.com/

MyOpenRouter

WGR614 V8 and DD-WRT update

Tysek

Add Your Reply

Sponsored Links

Please log in or register to participate in this community!