http://www.myopenrouter.com?src=category_rss MyOpenRouter - WGR614L Open Source Router Wed, 10 Mar 2010 05:05:44 GMT admin@myopenrouter.com MyOpenRouter 60 http://www.myopenrouter.com/brand/router/community.gif http://www.myopenrouter.com?src=category_rss http://www.myopenrouter.com/forum/thread/18051/Recover-WGR614L-when-there-is-only-CFE/?src=category_rss The flash chip of my WGR614L was corrupted. Therefore I got new flash chip and then designed a hardware board with ATMEL ATMega8535L microcontroller. I then programmed the flash chip and put CFE on it using the microcontroller. Now I want to get some help from you guys that what method should i adopt to put firmware on the router. TFTP or Jtag method ? Whichever you suggest kindly give me some instructions on how to use them when there is only CFE on the flash chip. Thanks in advance WGR614L Open Source Router Wed, 10 Mar 2010 05:05:43 GMT Syed Yasir Imtiaz http://www.myopenrouter.com/forum/thread/18051/Recover-WGR614L-when-there-is-only-CFE/#discussion?src=category_rss http://www.myopenrouter.com/forum/thread/17928/WAN-port-with-Vlan-Tagging/?src=category_rss Please can anyone help me with this configuration? I want WAN port of my wgr614v8 with DD-WRT build svn revision 12357M to access internet thru vlan tagged network with header eth0.511 for example. Setup / Configuration Sat, 06 Mar 2010 07:27:26 GMT surfman http://www.myopenrouter.com/forum/thread/17928/WAN-port-with-Vlan-Tagging/#discussion?src=category_rss http://www.myopenrouter.com/forum/thread/17902/Upgrade-WGR614v9-to-WGR614v8/?src=category_rss Hi last week i spend in upgrade of my cheap WGR614v9 (2MB Flash/8MB RAM) to WGR614v8. First of all i try with many RAM Chips until i found one working 32MB. Then i change flash chip with ST 25P32 - 4MB serial. I have fullflash from WGR614v8 and mod nvram_init to 0x000B my router v9 become v8 with 32MB RAM. Problem is when i update router with DD-WRT and he is recognised as Linksys WRT54G/GL/GS MAC Adresses of WAN and LAN are same and some leds are swapped (power=V(and is yellow) and Internet form green becomes yellow) Is this a normal behavior? WGR614L Open Source Router Fri, 05 Mar 2010 12:53:54 GMT surfman http://www.myopenrouter.com/forum/thread/17902/Upgrade-WGR614v9-to-WGR614v8/#discussion?src=category_rss http://www.myopenrouter.com/forum/thread/17781/Debricking-issues-with-WGR614L-does-not-enter-Programming-stage/?src=category_rss I recently had an issue with my WGR614L and finally found the time to wire in a serial connection. I attempted to debrick it earlier today, following the instructions here (they should be the same for both WGR614L and WNR3500L.) I have successfully re-flashed the WNR3500L using the same method countless times. Everything seems to work fine up until the point where I run the "put" command in tftp to send the new firmware to the router, which is connected via minicom. It successfully sends the file, and the router seems to have received it, but it does not enter the programming screen (see photos above of the windows I had open at the time) It sits there with the green power light flashing, the orange check mark lit solid, and doesn't do anything else. I can ping the router at 192.168.1.1. I have tried both the original NETGEAR firmware and DD-WRT (multiple builds.) I have tried multiple 30-30-30 resets, too. Any thoughts or suggestions? Troubleshooting Tue, 02 Mar 2010 04:55:42 GMT Peter Redmer http://www.myopenrouter.com/forum/thread/17781/Debricking-issues-with-WGR614L-does-not-enter-Programming-stage/#discussion?src=category_rss http://www.myopenrouter.com/forum/thread/17706/How-do-I...../?src=category_rss change channels? I learned va an app that my neighbor has wirelss also. My neigbor is on the same channel as I am. Thus I am interested in changing channel. Setup / Configuration Sat, 27 Feb 2010 12:09:38 GMT littlethunder http://www.myopenrouter.com/forum/thread/17706/How-do-I...../#discussion?src=category_rss http://www.myopenrouter.com/forum/thread/17615/Older-Lynksys-Modem-Need-Wireless-Router/?src=category_rss Hello, I have a Wireless-g card and I have an older lynksys modem. What do I need to get going completely wireless ? Someone tried to use my old wired router and a wireless g access point, but it didnt work. Can I just use a new wireless router ? Are they compatible ?? Troubleshooting Wed, 24 Feb 2010 18:41:23 GMT MidwestMama http://www.myopenrouter.com/forum/thread/17615/Older-Lynksys-Modem-Need-Wireless-Router/#discussion?src=category_rss http://www.myopenrouter.com/forum/thread/17409/Streaming-Strangeness/?src=category_rss I have a WGR314Lv8 with DD-WRT std build 13064 (dd-wrt.v24_std_generic.bin). Everything seems to work fine except accessing large files from a network share over wireless (via a netbook). If I try and copy a large file or stream ANY video file, the wireless connection on the netbook is lost. I can stream music fine (even quite large mixes) but even clicking on a video file on a remote share can cause the wireless to drop. It worked fine on the cheap POS Azurewave router I used before so I am thinking the problem is on the router/dd-wrt end. Any advice very gratefully received. Gary WGR614L Open Source Router Wed, 17 Feb 2010 15:41:11 GMT Gazziep http://www.myopenrouter.com/forum/thread/17409/Streaming-Strangeness/#discussion?src=category_rss http://www.myopenrouter.com/forum/thread/17292/unable-to-connect-to-wnr3500l-using-telnet/?src=category_rss Hi, Today, i powered up a brand new router for wnr3500l. I was able to open the web interface of the router using http://192.168.1.1 However i was unable to connect to using "telnet 192.168.1.1" the telnet client never succeeds in connecting to the telnet daemaon on the router. does anyone know how to check the telnet daemon is enabled on the wnr3500l routr? Thanks in advance... -Raghu WGR614L Open Source Router Fri, 12 Feb 2010 16:03:06 GMT Raghu http://www.myopenrouter.com/forum/thread/17292/unable-to-connect-to-wnr3500l-using-telnet/#discussion?src=category_rss