BrandonC - Community Contributions
Gallery: Recover Your WGR614L Using a Serial Console & Windows
By
BrandonC
on June 16, 2008 11:39 AM
Hopefully, you will never have to do this, but if you are like me and like to work on the bleeding edge of technology - sometimes things happen. (Of course, you might just enjoy getting...
Recover Your WGR614L Using a Serial Console & Windows
By
BrandonC
on June 16, 2008 11:32 AM
So, you've "bricked" your WGR614L, either through too much tinkering or just a fluke. You may have tried tftp through your network cable, you just can't get a ping or for any reason can't get it going again. Rather than panic, you can access your router by using a serial console!
Last Post: July 6, 2008 5:16 AM by Drone
Blocking the Internet with NETGEAR Routers
By
BrandonC
on June 8, 2008 5:02 PM
After I set up my new KWGR614 open source router, I thought it was time to add in our "No Internet after 9:00 PM" rule for one of the kids. I wanted to see if...
Ping - Explained
By
BrandonC
on April 21, 2008 10:37 AM
If you have been just getting into routers, networking and upgrades, you probably have seen a lot of folks talk about pinging. This should help you understand this utility. PING is short for Packet InterNet...
WGR614L and TFTP on Windows
By
BrandonC
on April 15, 2008 10:43 AM
Using Windows to send an image to your WGR614L is a little more tricky than using Linux. The reason why is because of how the CFE works or is designed - the CFE is the...
Difference between v8/L and v9
Thread started by
BrandonC
on April 13, 2008 4:06 PM
Can anyone tell me if there is a difference between the v8/L and the v9?
Last Post: May 3, 2008 2:12 PM by Nachi
WGR614L Router Setup and Installation Guide
By
BrandonC
on March 25, 2008 4:27 PM
This article will show you how to install and configure your NETGEAR WGR614L for most standard setups. For most folks, the installation is very easy and can be done in just a few minutes. But,...
Reset Procedures?
Thread started by
BrandonC
on March 21, 2008 9:11 PM
I saw this in the PDF for reset procedures. Weird deal, never saw a company that was not sure how to reset their own product.
Last Post: March 27, 2008 9:45 PM by BrandonC
Can I import KWGR614 config into my WGR614L
Thread started by
BrandonC
on February 25, 2008 8:03 PM
So, I just got my new WGR614L router. It would save me a lot of time if I can import the settings from my KWGR614 into it. Has anyone tried this? Is it possible?
Netgear is Promoting Myopenrouter.com!
Thread started by
BrandonC
on February 25, 2008 7:27 PM
I just received my new WGR614L router and was surprised to see a sticker on it promoting this website. Hopefully that will bring some good knowledgeable folks here to help answer and tweak our routers.
KWGR614 Open Source Router Installation and Setup
By
BrandonC
on January 15, 2008 1:00 PM
After years of using Linksys WRT54G routers, I decided that it was time to look into a newer setup for my system. I'm not currently having any problems, but my routers are the old V2...
Copyright © 2008
Capable Networks LLC.. All Rights Reserved.
RSS |
Privacy Policy |
Advertise With Us |
Terms of Use |
About Us |
Contact Us |
Site Map
Our Capable Community Network:
Drobo Space |
DVR playground |
MediaSmart Home |
Monster Community |
MotoDash |
My DigitalEntertainer |
My Open Router |
Presto Place |
Robo Community |
Sansa Community |
Sling Community |
TechLore |
TiVo Community
MyOpenRouter.com is not affiliated with NETGEAR®. NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks of their respective holder(s). © 2008 NETGEAR, Inc. All rights reserved.
