Need to Complete Rebuild

Thread started by hrlevy on March 2, 2008 11:17 AM

I need to know how to do a complete rebuild. It appears that all of the needed source code is not included with the download supplied from Netgear. If i change the ver number and...

Categories: WGR614L Open Source Router | Thread's Raw Score: 73,506 | 1  Comment | 23  Views

Last Post: March 3, 2008 7:10 PM by wrthack

Debug console

Thread started by hrlevy on March 1, 2008 1:20 AM

Has anyone used the debug console on a WGR614 yet. I have failed in all of my attemps to talk to it. My hardware is the recomended rs232-3v3 usb adapter cable. The cable works with...

Categories: WGR614L Open Source Router | Thread's Raw Score: over 220 thousand | 8  Comments | 88  Views

Last Post: June 16, 2008 11:38 AM by Peter Redmer

rebuilding of "PREBUILT" files

Thread started by hrlevy on February 29, 2008 2:42 PM

How do I rebuild the modules in the "..\bcm5354\src\prebuilt" dircetory??? the build instructions supplied do not rebuld these. As a test I tried to change the ver#. The only source module that contain the ver#...

Categories: WGR614L Open Source Router | Thread's Raw Score: 38,570 | 0  Comments | 23  Views

Device Recovery procedure Fails

Thread started by hrlevy on February 29, 2008 2:34 AM

The doc says to: 1. Power off the unit 2. Press and hold the RESET button at the rear panel 3. Power on to reboot the unit 4. Monitor the Test LED, and keep holding...

Categories: WGR614L Open Source Router | Thread's Raw Score: 50,066 | 7  Comments | 53  Views

Last Post: March 4, 2008 3:15 AM by hrlevy

Console Debug Interface

Thread started by hrlevy on February 28, 2008 10:38 PM

Has anyone gotten the "console debug interface" to work on the WGR614L?? if so, how did you do it?? I have connected the "RS232-3v3 to usb" but can not get any response from the WGR614L....

Categories: WGR614L Open Source Router | Thread's Raw Score: 31,395 | 0  Comments | 10  Views

Stil Can't get a good build for WGR614v8 code

Thread started by hrlevy on February 27, 2008 7:31 PM

For the 4th time I tried to build this code. First I did a full clean install of Fedora 8. Then I added in the additional "compat-8" stuff. Again down-loaded the 2 modules from the...

Categories: WGR614L Open Source Router | Thread's Raw Score: 87,643 | 4  Comments | 58  Views

Last Post: February 28, 2008 12:52 PM by Nachi

Can't find Fedora Core 2

Thread started by hrlevy on February 22, 2008 6:58 PM

I'm having trouble locating a download of "Fedora Core 2". It would be nice for Netgear to update their code to use the current tools. The oldest ver of Feroda shown on the site is...

Categories: WGR614L Open Source Router | Thread's Raw Score: 39,036 | 5  Comments | 39  Views

Last Post: February 28, 2008 11:35 AM by Peter Redmer

"step by step" guide to custom code on the WGR614L

Thread started by hrlevy on February 22, 2008 3:58 PM

Are there any "step by step" guides to putting custom code on the WGR614L ? I have already downloaded all available stuff for the WGR614L. It would be nice if there was a basic module...

Categories: WGR614L Open Source Router Open Source Projects and Firmware | Thread's Raw Score: over 173 thousand | 3  Comments | 95  Views

Last Post: July 2, 2008 7:32 PM by Nachi

Possible use for WGR614L

Thread started by hrlevy on February 21, 2008 1:36 PM

Is it possible to modifiy the "netgear orig" code so the rather than block selective sites only allow access to selected site???

Categories: WGR614L Open Source Router | Thread's Raw Score: 27,783 | 1  Comment | 13  Views

Last Post: February 21, 2008 5:15 PM by BrandonC