Latest dd-wrt with samba3 + ntfs support

Hi!

Very useful features for all...
Is your mod based on "big" built feature set?
Thanks,
Mat

Which build is this? Is there printer support as well?

Kong said: @Avmat: It is a std + usb + ftp + samba3 + ntfs Samba and ntfs support need a lot of flash space, so for a wnr3500l it is not possible to integrate these features into big. @taekwon3dan: Yes

svn#?

Hi,
it is nice compilation, but I have problem with set up permission. When I want to open folder "Share" in WinXP it is not possible or after open folder I'm not able to create subfolder, delete files etc...
I tried click right mouse button on folder "Share" but there is not possible set up permision for user. Maybe it is possible but not in my case.
How can I set permission for "Share" and subfolders. Ideally I need 3 folders and 2 users. Everyone can write and read from one folder and both can only read from third folder.
Can you advise me how can I set these permissions?

Sorry for my English I hope you understand my problem :-)

Kong:
Thank you for your advice.

If I understand when I want to have Share3 where will be only read permision for both users add to custom setup this paragraph:

[Share3]
comment = Restricted Area
path = /jffs/Share3
read only = Yes
guest ok = No
valid users = a
valid users = b

It is correct?

@kong

I want to run a ldna service.
I tried to install twonky which comes with optware.
The service is running but I can't connect with it by it's ip 192.168.1.1:9000
Do you have any sugestions of which ldna server I could use with this build that works?
Perhaps you've installed one youreselve.

Thanks Kong, this is what I need. Perfect. Thanks, thanks, thanks.

As I have read, installing Optware requires repartioning the external disk drive. I want to be able to connect the router to my NTFS external disk drive, but I have been wowed by the vast amount of data that is availablem, but unorganized/uncategorized.

Optware seems to require a certain amount of data which would need external storage. I do really not trust repartitioning my external NTFS drive, as I have gotten it back from RMA fixed after issues with running Linux and the external drive. I don't mind tweaking my router (3500L), but not the drive.

Kong:
I tried to set Samba according to your advice (comment from May 24, 2010 7:31 PM) but there is something wrong. Connection to Share1 (user1) work perfect but I not able to connect to Share2 (user2). When I want to connect to Share2 is displayed message with error:

Is not possible connect device: There is multiple connection to server and is not possible to use more than one user. Close other connection to server and try it again.

It is not exactly because my Windows are localized in Czech language :-) Do you know how I can solve this problem? I'm not sure where is problem (WinXp or Samba). 

Thank you for your help

First off: THANK YOU. This is a great package. Perfect for my needs and I am sure many many others.

I am a complete newbie to DD-WRT. If you had the time, could you offer some advice on how to share a printer with your FW. I have found things like this that help in general, but I am left wondering what might be different with your FW.

Thanks a ton.

So, I have done a ton of reading and am a little less of a newbie now.  :-)

I think my question now is why jffs has no space available?  It shows 4,224.00 KB / 0 for JFFS2.  As I have read, I need to do a ipkg install of p910nd.  However, I can't do so as /jffs has no space.  Is it set to Read Only?

Any help would be appreciated.

WNR3500L

Hi, is it possible to add and openvpn in this build?

I'm trying it out and it works great. Fantastic job! Thanks for putting together this firmware.

I'm currently getting about a 3.8 MB/sec transfer rate on my file transfers with the CPU and RAM usage basically at 100%. Is this normal? I know that the capabilities of the router's hardware are limited. Are there any samba tweaks that might help me get better read/write speeds?

I'm trying this out and it works fantastic. Great job!.

I'm in the middle of a fairly large file transfer and I'm averaging 3.8 MB/sec with the CPU and RAM usage at approximately 100%. My external HD is formatted to ext2. Is this normal performance for Samba on one of these routers? I know the hardware is pretty limited. Are there any tweaks to make samba work better?

Thanks, I will look forwart to this feature.

Kong said:

dragonator said: Hi, is it possible to add and openvpn in this build?

It's not a big deal to enable it in the build process, but I don't know yet how much flash it needs and if I can enable it along with the other features I added.

Hi
I was looking at the smb.conf in the /tmp directory. When i use the custom configuration field it puts ^M at the end of every line in there.

so i get

[global]^M
server string = Router^M
workgroup = Home^M
interfaces = br*^M
...
Will these character return symbols cause problems? I ask because i locked up my last router trying to apply this.

Thanks kong yeah was using putty, one last thing. I'm not able to get write access to any of the network drives. When i try to make a folder or drag n drop a file into it, it says i need permission to perform this action.

this is my setup file

[global]
server string = BCR BOX
workgroup = workgroup
interfaces = br*
bind interfaces only = Yes
map to guest = Bad User
smb passwd file = /var/samba/smbpasswd
private dir = /var/samba
passdb backend = smbpasswd
log file = /var/smbd.log
max log size = 1000
printing = none
load printers = No
usershare allow guests = Yes

[Public]
comment = Public Share
path = /mnt/Public
read only = No
guest ok = Yes
guest only = Yes
writeable = yes

[Share1]
comment = Restricted Area
path = /mnt/
read only = No
guest ok = No
valid users = newimage

Kong,
What and where is your latest release for this issue?
Tim