Here is some console info on the new WNR3500lv2 with the initial dd-wrt firmware loaded.I have a couple of these devices available for testing and have access to serial console.
http://www.myopenrouter.com/download/34850/DD-WRT-for-WNR3500Lv2-Initial...
[code]
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
Decompressing...done
CFE for WNR3500Lv2 version: v1.0.9
Build Date: Fri May 6 11:54:17 CST 2011
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
NFLASH Boot partition size = 524288(0x80000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.136
CPU type 0x19749: 480MHz
Tot mem: 131072 KBytes
Device eth0: hwaddr 74-44-01-2D-E5-F8, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Checking crc...done.
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ...... 2965200 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.24.111 ([email protected]) (gcc version 4.1.2) #1 Thu Dec 1 17:19:10 IST 2011
CPU revision is: 00019749
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 32767
HighMem 32767 -> 32767
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 32767
Built 1 zonelists in Zone order. Total pages: 32767
Kernel command line: console=ttyS0,115200 root=1f0f rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5357 rev 2 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126236k/131068k available (2348k kernel code, 4672k reserved, 356k data, 188k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
devfs: 2004-01-31 Richard Gooch ([email protected])
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
pflash: found no supported devices
Found a 0MB ST compatible serial flash
sflash: found no supported devices
nflash: squash filesystem with lzma found at block 6125
Boot partition size = 524288(0x80000)
Creating 16 MTD partitions on "nflash":
0x00000000-0x00080000 : "boot"
0x00080000-0x00200000 : "nvram"
0x00200000-0x00240000 : "board_data"
0x00240000-0x00280000 : "POT1"
0x00280000-0x002c0000 : "POT2"
0x002c0000-0x00300000 : "T_Meter1"
0x00300000-0x00340000 : "T_Meter2"
0x00340000-0x00380000 : "ML1"
0x00380000-0x003c0000 : "ML2"
0x003c0000-0x00400000 : "ML3"
0x00400000-0x00440000 : "ML4"
0x00440000-0x00480000 : "ML5"
0x00480000-0x004c0000 : "ML6"
0x004c0000-0x00500000 : "ML7"
0x00500000-0x02000000 : "linux"
0x005fb404-0x02000000 : "rootfs"
Broadcom Watchdog Timer: 0.07 initialized.
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <[email protected]>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
decode 1f0f
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 188k freed
start service
starting Architecture code for broadcom
starting hotplug
done
mknod: /dev/nvram: File exists
mknod: /dev/ppp: File exists
eth1: No such device
eth1: No such device
Booting device: Netgear WNR3500Lv2
Enable USB automount
Start ssh, ftp server and samba
Enable wl0_bss_enabled
loading et
et: module license 'Proprietary' taints kernel.
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.127
loading switch-core
loading switch-robo
roboswitch: Probing device eth0: found a 53115!
loading emf
loading igs
loading wl
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.100.127
[USB] checking...
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
insmod: usb-uhci.ko: module not found
USB Universal Host Controller Interface driver v3.0
insmod: usb-ohci.ko: module not found
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
insmod: printer.ko: module not found
usbcore: registered new interface driver usblp
[USB] check for drives....
/etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
/etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
eth1: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not permitted
eth1: Operation not supported
nbw = 20
eth1: Invalid argument
eth1: Invalid argument
eth1: Operation not supported
eth1: Operation not supported
sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
Algorithmics/MIPS FPU Emulator v1.5
br0: No such file or directory
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
br0: No such file or directory
eth1: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not permitted
eth1: Invalid argument
eth1: Operation not supported
nbw = 20
eth1: Invalid argument
eth1: Invalid argument
eth1: Operation not supported
eth1: Operation not supported
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
device br0 left promiscuous mode
device br0 entered promiscuous mode
device br0 left promiscuous mode
device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
cp: cannot stat '/tmp/mycron.d/*': No such file or directory
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
cp: cannot stat '/jffs/mycron.d/*': No such file or directory
cp: cannot stat '/mmc/mycron.d/*': No such file or directory
rmmod: n_hdlc: No such file or directory
Key is a RSA key
Wrote key to '/tmp/root/.ssh/ssh_host_rsa_key'
Key is a DSS key
device vlan2 entered promiscuous mode
Wrote key to '/tmp/root/.ssh/ssh_host_dss_key'
device vlan2 left promiscuous mode
SIOCGIFFLAGS: No such device
- setting default address to 192.168.1.1
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
umount: can't umount /tmp/smbshare: No such file or directory
rmmod: cifs: No such file or directory
rmmod: ipt_webstr: No such file or directory
rmmod: ipt_layer7: No such file or directory
rmmod: ipt_ipp2p: No such file or directory
rmmod: ebt_dnat: No such file or directory
rmmod: ebt_snat: No such file or directory
rmmod: ebt_mark_m: No such file or directory
rmmod: ebt_mark: No such file or directory
rmmod: ebtable_filter: No such file or directory
rmmod: ebtable_nat: No such file or directory
rmmod: ebtables: No such file or directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
rmmod: imq: No such file or directory
[code]
DD-WRT v24-sp2 custom (c) 2011 NewMedia-NET GmbH
Release: 12/01/11 (SVN revision: 17201M)
ÿ
DD-WRT login:
Login timed out connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
DD-WRT v24-sp2 custom (c) 2011 NewMedia-NET GmbH
Release: 12/01/11 (SVN revision: 17201M)
ÿ
DD-WRT login: root
Password:
==========================================================
____ ___ __ ______ _____ ____ _ _
| _ \| _ \ \ \ / / _ \_ _| __ _|___ \| || |
|| | || ||____\ \ /\ / /| |_) || | \ \ / / __) | || |_
||_| ||_||_____\ V V / | _ < | | \ V / / __/|__ _|
|___/|___/ \_/\_/ |_| \_\|_| \_/ |_____| |_|
DD-WRT v24-sp2
http://www.dd-wrt.com
==========================================================
Jan 1 00:02:24 login[1556]: root login on 'console'
BusyBox v1.13.4 (2011-12-01 17:17:08 IST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
[/code]
[code]
root@DD-WRT:~# uname -a
Linux DD-WRT 2.6.24.111 #1 Thu Dec 1 17:19:10 IST 2011 mips unknown
root@DD-WRT:~# cat /proc/cpuinfo
system type : Broadcom BCM5357 chip rev 2
processor : 0
cpu model : MIPS 74K V4.9
BogoMIPS : 239.20
wait instruction : no
microsecond timers : yes
tlb_entries : 64
extra interrupt vector : no
hardware watchpoint : yes
ASEs implemented : mips16 dsp
shadow register sets : 1
VCED exceptions : not available
VCEI exceptions : not available
dcache hits : 2147483648
dcache misses : 1497412975
icache hits : 2147483648
icache misses : 3972660136
instructions : 2147483648
[/code]
[code]
root@DD-WRT:~# cat /proc/meminfo
total: used: free: shared: buffers: cached:
Mem: 129622016 20369408 109252608 0 2363392 7598080
Swap: 0 0 0
MemTotal: 126584 kB
MemFree: 106692 kB
MemShared: 0 kB
Buffers: 2308 kB
Cached: 7420 kB
SwapCached: 0 kB
Active: 1005 kB
Inactive: 1761 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 126584 kB
LowFree: 106692 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
Mapped: 303 kB
Slab: 295 kB
CommitLimit: 63292 kB
Committed_AS: 3612 kB
PageTables: 2432 kB
VmallocTotal: 1015800 kB
VmallocUsed: 16 kB
VmallocChunk: 1015784 kB
[/code]
[code]
root@DD-WRT:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00080000 00020000 "boot"
mtd1: 00180000 00020000 "nvram"
mtd2: 00040000 00020000 "board_data"
mtd3: 00040000 00020000 "POT1"
mtd4: 00040000 00020000 "POT2"
mtd5: 00040000 00020000 "T_Meter1"
mtd6: 00040000 00020000 "T_Meter2"
mtd7: 00040000 00020000 "ML1"
mtd8: 00040000 00020000 "ML2"
mtd9: 00040000 00020000 "ML3"
mtd10: 00040000 00020000 "ML4"
mtd11: 00040000 00020000 "ML5"
mtd12: 00040000 00020000 "ML6"
mtd13: 00040000 00020000 "ML7"
mtd14: 01b00000 00020000 "linux"
mtd15: 01a04bfc 00020000 "rootfs"
[/code]
[code]
root@DD-WRT:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 5.4M 5.4M 0 100% /
root@DD-WRT:~#
[/code]
Recent comments