hello,
i have ddwrt installed on my device now
i want to install tomato i got the tomato image ...
want now??
i dont know hihi
please tell me
greets dominic
Rehabilitation, underground utilities, sewer installation and repair
American Sewer and Utilities has consistently demonstrated excellence in the design and construction of a myriad of projects encompassing underground utilities, site development, leach fields, pump stations, landscaping, sanitary sewer, and municipal & residential rehabilitation. Our distinguished team comprises seasoned professionals and skilled artisans, dedicated to providing superior construction consultation and management servicesRecent comments
- After the initial Kong Mod 11 months 4 weeks ago
- Working the EXACT same 12 months 1 hour ago
- While the "5 Easy Steps" 1 year 5 days ago
- R8000P would be grate to see. 1 year 6 days ago
- Have a R8000 but ordered a 1 year 6 days ago
so i did this
^^
now i can login into tomato i think but there is still an old password i think i tried different combinations :S
root admin
etc...
please help me
greets
ps.: i forgot to do "nvram get http_passwd" before :(
no it wont work -.-
damn
after the 30-30-30 reset still not working
what about new flashing???
in the boot up phase
i see that if i power on and connect to it the orange light next to the power light is on
Oo
greets dominic
-.- omg
i`m sorry -.-
i didn`t flash the original netgear before ...
but i told ddwrt to delete itself with 2 commands out of here ....
then i flashed tomato :S
should work ????
hmm well
i only have a jtag cable ^^
what about that?
hmm .. u need to have a usb-serial cable to access the console and see how far ur boot is happening properly ....
Most probably u have corrupted the flash n in the boot sequence u r not able to get the rootfs ...
these things will be clarified once u can access the console ....
i found a mobile phone cable ^^
but i dont now the polarity "bzw." the pinout
i have 3 cables...
some ideas?^^
greets
actually I havn't use a mobile fon cable for this purpose so can't say much abt it ...
I used my own usb->serial cable ....
U may find following information useful :
http://www.myopenrouter.com/article/10811/Hacking-Your-NETGEAR-WGR614L-H...
Let me know if u still have any doubts ...
what if i test out with my serial cable?? i know ir worked sometimes but i forgot the pinout of it ^^
is there a chance to destroy the board with testing the cable pinouts??
greets
cant i test it with a multimeter???
some ideas?
greets ^^
testing with multimeter will be safe .... u can do that ..
and how????
^^
OK ... u first neeed to go through the spec of board to find its tx and rx pins ... Then coming to cable u can check using multimeter at two ends of the cable to find out its tx and rx pins ... then connect tx of board to rx of cable and vice versa and that shud do ....
let me know if u still have any doubts ..
"Then coming to cable u can check using multimeter at two ends of the cable to find out its tx and rx pins ... " how????? do you have IM ?
greets
basically one end of the cable shud be a USB end ....so from USB spec u know the tx and rx pin of d USB end ...
then using multimeter between USB end and other end of ur cable u can check out for the tx and rx pins ...
i have a serial phone cable .... no usb i`m sorry :(
greets
OK ... then I think u will have to arrange a USB->serial cable .... I m not sure whether a simple serial cable will serve ur purpose or not ...
wich one should i buy???
A simple USB to serial cable ... It has been shown in the following article :
http://www.myopenrouter.com/article/10811/Hacking-Your-NETGEAR-WGR614L-H...
Do let me know if u need any further clarification ....